
Flatline Van Co.
Transit Van Rear Door Platform
Indexed listing. WNDR Built doesn't sell this product; the button opens flatlinevanco.com.
A rear-door base for changing Transit gear loads
This platform adds rear-door mounting space for gear such as MaxTrax, Rotopax, skis and snowboards. Flatline also describes carrying bikes with a 1Up tray. The plate sits flush with its surrounding tube frame to leave room for loading accessories.
Driver- and passenger-side versions provide different surface widths. The mounting pattern lets accessories use different positions, and Flatline designed the platform so those accessories can be swapped as the gear carried changes.
Mounting pattern
Flatline lists more than 200 mounting slots and holes, including 1/2 in and 3/8 in holes.
Frame & structural brackets
The platform combines a 1.75 in aluminum tube frame, 3/16 in aluminum mounting plate and stainless steel structural brackets.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Flatline Van Co.
- 2015+ Transit 150/250/350 | 130"/148"/148" EXT | Mid/High Roof
- 2023–2024 Transit Trail | 148"/148" EXT | Mid/High Roof
Choose the rear door
The platforms differ by door and mounting-surface width.
Transit Rear Door Platform (Passenger)
- Passenger-side platform with a 23.75 in wide mounting surface.
Transit Rear Door Platform (Driver)
- Driver-side platform with a 30 in wide mounting surface.
Driver-door opening limit
The driver-side guide warns that opening the rear door past 90° can bring the platform into contact with the van.
Drilling required
Both versions require an exterior attachment hole and the interior mounting/access preparation in their guides. Driver side: enlarge the outside hole to 27/64 in and add a 9/32 in or similar side hole only if absent. Passenger side: drill the exterior and interior mounting holes to 27/64 in. Deburr and paint exposed edges as specified.
California Proposition 65
Flatline warns that this product can expose you to lead and lead compounds, DEHP and bisphenol A (BPA), which California identifies as causing cancer and birth defects or other reproductive harm.
Hinge compatibility
Flatline lists compatibility with both hinge types.
Installer requirement
Flatline recommends professional installation of aftermarket accessories; its guide requires a professional installer or other qualified person if you have no mechanical experience and are not thoroughly familiar with the installation procedures.
Before use
Flatline requires checking mounting points and attachments before use and regularly inspecting the product for wear or damage.
Specs, parts & installation
Frame & construction
| Frame | 1.75 in round aluminum tube |
|---|---|
| Mounting plate | 3/16 in aluminum |
| Structural brackets | Stainless steel |
| Accessory holes | Patterned 1/2 in and 3/8 in holes |
| Suggested weight limit | Flatline states a suggested weight limit of 200 lb |
Driver-side surfaces
| Hole-pattern surface | 54 in tall × 24 in wide |
|---|---|
| Mounting surface | 59.38 in tall × 30 in wide |
Passenger-side surfaces
| Hole-pattern surface | 54 in tall × 18 in wide |
|---|---|
| Mounting surface | 59.38 in tall × 23.75 in wide |
What’s in the box
Platform & door supports
One platform for the selected rear door, upper and lower hinge brackets, lower frame brace and an internal door brace/backer.
Templates & mounting hardware
Exterior/front and interior/side drill templates with the mounting hardware for the chosen side.
Side-specific third mount
Driver: bushing cap, tall and short bushings and sealing washer. Passenger: bonded sealing washer and door backer with a neoprene pad.
Installation at a glance
Flatline’s driver guide estimates 1–2 hours; its passenger guide estimates 2 hours. Both suggest additional help for some steps.
Support the door to prevent twisting while fitting the hinge brackets and check closing clearance before tightening the factory hinge bolts. Remove the interior panel and peel back the relevant vapor-barrier corner. Prepare the mounting holes, then secure the platform, internal brace/backer and lower frame brace with assistance.
Side-specific third mount
- Driver: secure the bushing assembly and internal brace with only slight compression of the tall bushing; check door operation before final tightening.
- Passenger: place the door backer’s neoprene-padded flange against the outer door skin, align it with the inside mounting hole and secure it as directed in the guide.
Lead Time
Flatline’s FAQ lists in-stock dispatch in 1–2 business days and free lower-48 shipping; its Shipping policy lists flat-rate/economy options, with no-charge economy sometimes offered for longer lead times and typical LTL delivery of 7–21 business days.
Read Flatline Van Co. lead time policy on WNDR BuiltWarranty
Flatline’s Refund policy gives the original purchaser a one-year, non-transferable limited warranty covering product cost only, excluding installation, labor, freight and damage from racing, competition or trail use; alteration, modification or improper installation voids coverage.
Read Flatline Van Co. warranty policy on WNDR BuiltReturns
Flatline’s Refund policy accepts returns with a pre-authorized RMA within 30 days of receipt for unused, resalable items in original packaging, with a 20% restocking fee and customer-paid return shipping unless Flatline erred; freight returns require coordination, clearance/garage-sale/final-sale items are excluded, and custom or made-to-order items may be non-returnable.
Read Flatline Van Co. returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon