
Aluminess
Front Winch Bumper - 2019-24 Sprinter
Indexed listing. WNDR Built doesn't sell this product; the button opens aluminess.com.
An aluminum bumper built around a steel winch tray
This front winch bumper replaces the Sprinter’s factory front bumper with an aluminum outer shell supported by a steel winch tray. The tray bolts to the frame, carries the winch mounting position and provides the attachment for the aluminum bumper.
Three configurations provide different amounts of front coverage: full brush guards and a bull bar, a bull bar alone, or no guards. Aluminess lists two D-ring recovery points and pre-drilled sensor mounts on every configuration. The outer shell uses 6061 and 5052 aluminum with a textured black powder coat.
A sensor carriage and window accommodate the factory front radar sensor. A separate bracket carries the air temperature sensor, while parking sensor retainers and wiring attachment holes allow the original equipment to be transferred. A hitch receiver is sold separately; the sensor and chassis conditions are set out in Fitment.
Full-coverage light openings
The full-coverage version has four light cutouts.
Adjustment after installation
The installation sheet permits front radar adjustment after bumper installation by removing and reinstalling the front two sensor-window bolts.
Manufacturer-listed fitment & checks
Vehicle fitment
As listed by Aluminess
2019–2024 Mercedes-Benz Sprinter, as Aluminess lists it: the 1500 for 2019–2023 and the 2500, 3500, 3500XD and 4500 for 2019–2024.
Choose the front coverage
Aluminess offers three bumper configurations.
With Brush Guards
- Bull bar and brush guards
With Bull Bar
- Bull bar only
Without Bull Bar and Brush Guards
- No bull bar or brush guards
Winch and solenoid
A winch is not included. Aluminess says the bumper works with most leading winch brands, though solenoid relocation may occasionally be required because winch makers change their designs.
Hitch receiver
A custom hitch receiver option is sold separately.
Aftermarket vehicle conversions
Aluminess states all its products are designed to fit factory manufactured vehicles and that some aftermarket vehicle conversions are incompatible with Aluminess products.
Cutting the airflow skirt
The installation sheet requires cutting the airflow skirt’s rubber gasketing around the hose lines for removal, taking care not to cut the hoses.
Front radar alignment
The installation sheet requires the sensor to be level left-to-right (±1°) and as perpendicular to the road as possible (±3°); start at the fourth position (5 degrees) and verify alignment in the vehicle.
California warning
Aluminess’s product page carries the California warning: “Cancer and Reproductive Harm - www.P65Warnings.ca.gov.”
Models in the installation sheet
The installation sheet says the bumper is compatible with the Sprinter 1500, 2500 and 3500, and that 3500s may require specialized tooling and/or additional hardware. It adds that a Sprinter 3500 may or may not have the factory crossmember bolts and threaded inserts, in which case additional tapping and hardware may be required. The sheet does not mention the 3500XD or 4500.
Sensors and cameras
Aluminess states the bumper is fully compatible with factory sensors and cameras. Per the installation sheet, parking sensor retainers are sold separately; Aluminess’s product page lists an optional Parking Sensor Kit.
Other Sprinter years
Aluminess lists a separate front bumper for the 2014–2018 Sprinter.
Use and legal compliance
Aluminess states its products are designed for off-road vehicle use and may exceed the vehicle’s factory-designed capabilities. It does not guarantee compliance with local vehicle laws; purchasers must establish suitability and legal compliance before use.
Specs, parts & installation
Bumper construction
| Material | 6061 and 5052 aluminum skin with a steel winch cradle |
|---|---|
| Finish | Textured black powder coat |
| Full-coverage bull bar | 2" (2.375” OD) |
| Full-coverage brush guards | 1.5" (1.9” OD) |
| Recovery points | Two D-ring recovery points on every configuration |
Shipping dimensions & weight
| Height | 36 IN. |
|---|---|
| Width | 48 IN. |
| Depth | 87 IN. |
| Shipping weight | 220 LBS. |
What’s in the box
Bumper and tray
Aluminum front bumper in the selected configuration
Steel winch tray
Supports and sensor bracket
Fender support brackets (left and right) and plastic support brackets (left and right)
Air temperature sensor bracket
Mounting hardware and recovery points
Hardware per the installation sheet: M8-1.25 × 40 mm bolts (8) with M8 nuts (8), 5/16 in stainless washers (8) and split lock washers (16); 1/2-13 × 1-1/2 in grade 8 bolts (8) with 1/2 in washers (12), split washers (6) and nylon-locking nuts (4); 1/4-20 × 1 in stainless button head bolts (4), a 1/4-20 × 5/8 in carriage bolt, 1/4 in washers (9), nylon-locking nuts (4), a thin nut, an O-ring and an anti-seize packet
Two D-ring recovery points (per the product page)
Installation at a glance
Aluminess’s installation sheet requires two or more people. The steps: remove the grille, push-pin rivets and bolts, unclip the front camera if applicable; unplug and remove the factory plastic bumper, then remove the collision prevention sensor and plastic sensor bracket, the eight bolts holding the stock steel bumper (using a putty knife and hammer if sealant holds it), and the airflow skirt (the rubber gasketing is cut around the hose lines); loosen only the bottom crossmember bolts and uninstall the outer fender supports. Mount the steel winch tray to the frame using eight supplied M8 bolts as studs and reinstall the factory hardware through the tray. Install the front radar sensor into its carriage with the fourth position (5 degrees) as the starting setting, then verify alignment in the vehicle: level within ±1° left to right and as close to perpendicular to the road as possible (±3°), the parking sensor retainers if used, and the air temperature sensor bracket. Install the fender brackets before sliding the aluminum bumper onto the tray, then install the plastic support brackets, tighten the 1/2 in hardware, reconnect the sensors, reinstall the grille, drive 15 to 30 minutes to check the sensors, and verify bolt tightness after 100 miles. Aluminess says to apply anti-seize to stainless hardware. Tools listed: standard and metric wrench and socket sets, Torx wrench/bit set, flat head screwdriver, hammer, putty knife, razor blade or box cutter and painter’s masking tape. Tools are not included.
Lead Time
Read Aluminess lead time policy on WNDR BuiltWarranty
Read Aluminess warranty policy on WNDR BuiltReturns
Read Aluminess returns policy on WNDR BuiltWhat are people saying?
Find owner feedback, discussions, and installation videos for this product.
Searches use the manufacturer and product name and open in a new tab. Results may include similar products.
WNDR Built Community
Our community blog is coming in the future.
Community · Coming soon